fenderlocust85

pop a lock from Fiat 500 makes it simple to open doors and start your vehicle. However, there are many reasons the fob could stop working. This could be due to a dead battery, water damage, problems with receiver modules, as well as interference. This listing is for a NEW replacement Fiat Flip Key Remote – look-alike Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here for Locksmith Search). It comes with trunk, lock and unlock buttons. Dead Coin Battery A dead battery is the most common reason for your 500 key fob being inoperative. Modern key fobs have an operating range that is limited and must be within only a few inches from the vehicle in order to work. If you are far from your vehicle when you press the key fob button the car won't respond and will display an “Key Fob Not Detected” message in the instrument cluster. If this happens, replace the battery of your coin cell (Part number CR2032) by a new one from a reputable manufacturer such as Panasonic, Duracell, or Energizer. You can find them in the local hardware store or online. You can test the battery of your coin-cell by pressing the buttons while standing near your Fiat 500. The parking lights should blink and the key fob will operate the lock and unlock switches. If the key fob doesn't function after replacing the battery, it might be damaged by water that blocks it from connecting to the receiver module inside your vehicle. Water damage can occur in a number of ways, ranging from the slightest splash to submerging your fob in salt water at the beach. If you believe your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this doesn't work your fob is likely to need to be reset by a professional auto locksmith or dealer. Water Damage Water damage can occur if you immerse the fob into the ocean, or wash it in a machine. Saltwater can cause the circuit board to short, and eventually end up dying. It's not a good thing to soak the fob in water, but don't give it up even if you accidentally drop the fob in water or fail to take it out of your pants pocket. First remove the battery from the fob. Clean the electronic chip using isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Check the fob to determine if it's functioning. If the key doesn't function, it may need to be reprogrammed. This is usually done by an auto locksmith or dealer. If the key is a newer model and hasn't been programmed to your vehicle it is likely to need to be replaced completely. A professional locksmith for cars can complete this simple process. The locksmith needs to cut the key to match the ignition of your car. The locksmith will also have to program your fob into the car's system. This is a fast and cost-effective process which can be completed on the next day. Receiver Module Issues One of the main reasons why your 500 key fob won't be working is that it's simply out of range. The remote's range is of 30 feet, so when you're too far from your car, it won't respond to your commands. It is possible to fix this by moving the remote closer to your vehicle until it responds. If your fob does not work after replacing the coin battery, also called a “button”, “watch” or “button” or “button”, it could be due to a problem with the circuit board inside. In most cases, reprogramming the fob will resolve this problem. There are instructions on how to do this for the majority of vehicles by searching YouTube or looking through the owner's manual. It could be necessary to replace the metal clips that hold the coin batteries in the correct position. If they lose tension it could prevent your coin battery from sitting properly and cause your remote to malfunction. In rare instances, the fob may be out of the vehicle's sync because of hardware or software issues. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances it may be necessary to install the software again in your body control module as well. Interference In addition to a dead battery on a coin The key fob might not be receiving or transmitting the signal due to interference. This can occur when the key fob is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons why the key fob could not function include a poor connection to the buttons, damage to the internal chip or water damage. If the key fob been unable to function for a while in the middle of the night, or after trying everything you can at home to solve it e.g. replacing batteries, reprogramming or using the spare key fob, it could have a damaged receiver module on your 500. The receiver module, located under the dashboard, detects radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets. Luckily, there is an easy way to reset all of the on-board systems in your 500 and include the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Then reconnect the battery. This will erase any remaining electricity, and restart the computer of your car. This will help you get your key fob working again. If the issue persists, you should seek out an expert technician. They will be able to determine the exact cause of your problems.